7200BX MANUAL PDF

Vujar Do not ship LiPo batteries to Horizon. By submitting the item for service you are agreeing to payment of the service without notification. Besides eliminating the mechanical complexity of a flybar, the BeastX technology built into the ARBX system lets you quickly fine-tune stability, cyclic response and tail response without touching a single linkage or require special software. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Author:Zulurisar Daitaur
Country:Nicaragua
Language:English (Spanish)
Genre:Science
Published (Last):15 April 2006
Pages:216
PDF File Size:11.50 Mb
ePub File Size:18.93 Mb
ISBN:643-5-59263-692-5
Downloads:28674
Price:Free* [*Free Regsitration Required]
Uploader:Mijind



The ARBX must be in a low vibration position, such as the receiver or gyro platform. The mounting platform must be perpendicular to the main shaft. Helicopters usually have enough room on the frame to separate the main feeder antenna and the optional remote receiver.

The servo connector pins must always point toward the front or rear of the helicopter. Make sure the edges of the ARBX are all parallel with the corresponding axes of the helicopter. Page 8: Setup Procedure Setup procedure Power on the transmitter first.

The ARBX initializes when the receiver is powered on. Do not move the ARBX or the helicopter while the receiver is initializing. You can lay the helicopter on its side to prevent it from moving in windy conditions. Receiver Initialization Cycle 1. LEDs cycle and then the firmware version will display for 3 seconds. LEDs H through N cycle to initialize the receiver inputs. LEDs A through G cycle to calibrate the sensors. The swashplate moves a small amount and the Status LED turns solid after initialization completes.

The ARBX will also automatically exit the menu after 4 minutes of inactivity. To see a complete Spektrum servo reference chart, refer to the servo chart on spektrumrc. Page 11 C. There are a few tail servos available that use a different center position pulse length. Page 12 E. Setting the Tail Servo Endpoints Adjust the limit of the tail rotor blades to achieve the best throw.

The best throw is determined by either the maximum possible control travel of the tail slider or the maximum allowed tail rotor blade angle of attack. Make sure the tail rotor blades move in the correct direction see your helicopter manual for more information. Page 13 G. Adjusting the Swashplate Servo Centering Menu point G electronically adjusts the center point of the cyclic servos. Page Swashplate Mixer H.

You can also use any swashplate geometry by selecting User Defined PC software required. Refer to your helicopter manual for more information on CCPM. Page 15 I. Setting the Swashplate Servo Directions Menu point I ensures the swashplate servos are moving correctly. Try each of the four possible combinations until the swashplate moves correctly. Page 16 J. This will cause unwanted flight behavior.

Move the rotor blades so that they are parallel to the tail boom. Page 17 L. Adjusting the Cyclic Swashplate Limit Menu point L adjusts the maximum possible tilting of the swashplate for aileron and elevator. The deflection is limited in a circular path, similar to a cyclic ring function, preventing swashplate binding at full aileron and elevator travel. Carefully move the sticks for aileron, elevator and pitch to all maximum endpoints.

Page 18 4. If the swashplate changes direction and rotates against the direction of the helicopter, use the rudder stick to change the direction. Push the setup button to save the selection and exit the Setup Menu N. The setup steps of the ARBX are finished.

It is now necessary to continue setting up the dials and parameters options.

ICEA P-32-382 PDF

Spektrum AR7200BX Manuals

Dalkree You must include this request with your item submitted for service. Electronics and engines requiring inspection or repair should be shipped to the following address: As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. What this Warranty Covers: Horizon reserves the right to inspect any and all Product s involved in a warranty claim. By submitting the item for service you are agreeing to payment of the service without notification.

IBANEZ S520EX MANUAL PDF

Spektrum AR7200BX User Manual

The ARBX must be in a low vibration position, such as the receiver or gyro platform. The mounting platform must be perpendicular to the main shaft. Helicopters usually have enough room on the frame to separate the main feeder antenna and the optional remote receiver. The servo connector pins must always point toward the front or rear of the helicopter. Make sure the edges of the ARBX are all parallel with the corresponding axes of the helicopter.

CATERPILLAR 924HZ PDF

7200BX MANUAL PDF

Fegal Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. By submitting the item for service you are agreeing to payment of the service without notification. Besides eliminating the mechanical complexity of a flybar, the BeastX technology built mnual the ARBX system lets you quickly fine-tune stability, cyclic response and tail response without touching a single linkage or require special software. In addition you will be kanual for return freight. Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date.

Related Articles