BASLER BE1-27 PDF

It is loaned for confidential use, subject to return on request, and with the mutual understanding that it will not be used in any manner detrimental to the interest of Basler Electric. Revisions are listed in reverse chronological order. Page 6 This page intentionally left blank. Page 8 This page intentionally left blank. The BE Undervoltage Relay will detect this low voltage condition and trip. Critical applications requiring continuous motor operation and applications where overloads during start-up may be maintained for a given time period, usually have a definite time or inverse time delay characteristic incorporated to avoid unnecessary tripping during low voltage dips.

Author:Tabei Mejas
Country:Mexico
Language:English (Spanish)
Genre:Science
Published (Last):13 April 2004
Pages:406
PDF File Size:1.14 Mb
ePub File Size:4.33 Mb
ISBN:634-5-22319-140-3
Downloads:54185
Price:Free* [*Free Regsitration Required]
Uploader:JoJotaur



Inverse Time Inverse curve types are defined by the Style Chart and are represented by the curves shown in Section 3. Inverse time is adjustable from 01 to 99 in increments of Table Continuously adjustable over the range defined by the style number.

Page 12 Target Reset Lever Linkage extending through bottom of front Optional cover pushed to reset the magnetically latching target indicators. Target Indicators Magnetically latching indicators are tripped to Optional red to indicate that an undervoltage or overvoltage output relay has been energized. The transformer provides a high degree of isolation. Page 15 Range 2 Range 3 Range 4 D Page 16 Range 2 Range 3 Range 4 D Page 17 Page Targets Target indicators must be manually reset.

This new design created three, wide range power supplies that replace the four previous power supplies. Style number identifiers for these power supplies have not been changed so that customers may order the same style numbers that they ordered previously. Typical internal connections are shown in Figures through Typical ac connections are shown in Figure Typical dc connections are shown in Figure Be sure to check model and style number against the options listed in the Style Number Identification Chart before connecting and energizing a particular relay.

Page 21 Figure Page 22 Figure Page 23 Figure Page 24 Figure Page 25 Figure Page 26 Figure Page 27 Figure Page 28 Figure Page 29 Figure Page 30 Figure Page 31 Figure Page 32 Figure Page 33 Figure Page 34 Figure If a relay fails an operational test, or is an adjustment discloses a faulty relay, refer to Section 6.

Test indicator states will be opposite for normally closed output contacts. Pickup and Dropout Test Circuit Diagram Page 39 Figure In units with Sensing Input Range 3 or 4, all pickup and test indicators will be extinguished.

Page Timing This concludes the pickup test for Relay Model BE NOTE Steps 7 and 8 apply only to overvoltage functions. Step 7. Page 41 Table The operational test procedure of Section 5 provides an adequate check to verify proper operation of the relay. Most components are on conformally coated PC boards. In-house replacement of individual components may be difficult and should not be attempted unless appropriate equipment and qualified personnel are available.

The substantive changes to date are summarized below. This manual is also suitable for:.

ARTHUR BAROODY PDF

Basler BE1-27 Manuals

Please review your request for missing or invalid information, then try again. By sending us your information, you are affirming your agreement with our Privacy Policy. You will not receive unsolicited communications. Submit Request Quote Request received! Thank you for requesting a quote from us. A member of the GID Industrial team will reach out to you shortly.

H MOYSS NUSSENZVEIG PDF

Basler BE1-27 Manual

Inverse Time Inverse curve types are defined by the Style Chart and are represented by the curves shown in Section 3. Inverse time is adjustable from 01 to 99 in increments of Table Continuously adjustable over the range defined by the style number. Page 12 Target Reset Lever Linkage extending through bottom of front Optional cover pushed to reset the magnetically latching target indicators. Target Indicators Magnetically latching indicators are tripped to Optional red to indicate that an undervoltage or overvoltage output relay has been energized. The transformer provides a high degree of isolation.

Related Articles