IBANEZ S520EX MANUAL PDF

Tebei Products and specifications are subject to change without notice. Solid Body Electric Guitars. Loosen the pressure pad lock screws on the top lock with a 3. Tighten the string stopper bolt.

Author:Mikalkis Nilabar
Country:Bermuda
Language:English (Spanish)
Genre:Environment
Published (Last):8 March 2009
Pages:407
PDF File Size:16.79 Mb
ePub File Size:16.49 Mb
ISBN:951-7-62443-384-5
Downloads:17470
Price:Free* [*Free Regsitration Required]
Uploader:Kazihn



Tebei Products and specifications are subject to change without notice. Solid Body Electric Guitars. Loosen the pressure pad lock screws on the top lock with a 3. Tighten the string stopper bolt. Insert the tremolo arm into the arm socket and firmly push down until the arm snaps into place Note: Intonation adjustment is usually necessary when new strings are fitted it can also be affected by the angle of the tremolo unit.

Turn the notched wheel 4 To raise or lower the bridge. Occasionally, there are times when the neck may need adjustment. To reduce the torque, remove one bushing on the lower side.

To allow the arm to swing freely. Retune the guitar to the proper pitch and check the angle. SEX — The purpose of this is to accommodate for different tunings or different gauges of strings. Play the harmonic at the 12th fret, compare it to the fretted noteat the 12th fret, these notes should read the same on the tuner.

Wind the string around the tuning machine and tune to pitch 6. All lbanez guitars use A for a standard pitch. The truss rod is adjustable at the headstock using as allen wrench or an adjustment wrench.

The tremolo arm is placed in the hole in the bridge plate and inserted into the threaded block. Raise or lower the tremolo to the desired string height using a 3mm allen wrench. Play the harmonic at the 12th fret, compare it to the fretted note at the 12th fret, these notes should read the same on the tuner.

Wiring Diagrams The height adjustment of the tremolo can be set by using the two 4mm adjustment screws 2 on manua side of the tremolo unit. The height adjustment of the tremolo can be set by using the two 3mm adjustment screws on either side of the tremolo unit. Insert the mamual arm into the arm socket and turn the Arm torque adjustment nut A clockwise until it stops. Make sure the truss rod is properly adjusted before adjusting the action. On the bass plate there are two holes for each saddle lock down screw.

To check the intonation: Using a Phillips head screw driver, turn the Spring tension adjustment screw and adjust the length of the spring.

Over adjustment can result in damage to the instrument and will no be covered under warranty. If the intonation is still not correct repeat steps 1, 2 and 3. To adjust the string height of the saddles use a 1.

Height adjustment is made by adjusting the 2mm allen screws on either side of the bridge. Wiring Diagrams When the guitar is properly adjusted, tighten the top lock pressure pad screws. Tremolo Angle Adjustment The tremolo system should sit parallel to the surface of the guitar body, as shown in the illustration.

Remove the tremolo cavity cover plate from the back of the body. All guitar necks are subject to great stress as a result of string tension, humidity or changes in climactic conditions. Loosen the heigth adjustment screw 5 ibahez both sides of the bridge using a 2 Phillips. After changing the desired strings retune all the strings to the proper pitch and tighter the top lock pressure pad screws.

Note For ease in retuning. Most 10 Related.

EA800 ASUS PDF

S520EX (2005–2009)

Bajas Make sure the truss rod is properly adjusted before adjusting the action. This is caused by the string vibrating. To replace the bushings, remove the bushings by spreading opening the bushing until it is removed. The tremolo arm is placed in the hole in the bridge plate and inserted into the threaded block. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips 2.

H MOYSS NUSSENZVEIG PDF

IBANEZ S520EX MANUAL PDF

Dozragore This adjustment should be performed periodically and only by qualified repair personnel. The Saddles are preset on the plate. Both bushings should be completely hidden. Only loosen the screw enough to move the saddle. If the 12th fret harmonic pitch is lower than the fretted note, the saddle needs to be moved back. Raise or lower the tremolo to the desired string height using a 3mm allen wrench. Always loosen the Stud lock screws counter clockwise with a 1.

Related Articles